Popular Science | What is fiber acetate? - garment manufacture_garment Factory

Acetate fiber was born in the early 20th century. It was successfully trial-produced and industrialized by the United Kingdom in the early 1920s. It is currently the second largest fiber among cellulose fibers. The second largest variety of viscose fiber. Acetate fiber can be used to make textiles, cigarette filters, film bases, plastic products, etc.

1. Introduction to acetate fiber

Cellulose acetate, the English name is cellulose acetate, referred to as CA. Acetate fiber is divided into diacetate fiber and triacetate fiber, which is a type of man-made fiber. Chemical fibers are made from cellulose as raw material and converted into cellulose acetate through chemical synthesis. First prepared in 1865, it is an acetate ester of cellulose. A thermoplastic resin obtained by esterifying cellulose with acetic acid or acetic anhydride under the action of a catalyst. It is a chemically modified natural polymer obtained by esterifying the hydroxyl groups in the cellulose molecule with acetic acid. Its properties depend on the degree of acetylation.

2. Classification of acetate fiber

According to the hydroxyl group in cellulose The degree of substitution by acetyl groups can be divided into diacetate fiber and triacetate fiber.

Diacetate is a type of acetate formed after partial hydrolysis, and its degree of esterification is lower than that of triacetate. Therefore, the heating performance is not as good as that of trivinegar, the dyeing performance is better than that of trivinegar, and the moisture absorption rate is higher than that of trivinegar.

Triacetate is a type of acetate that does not undergo hydrolysis and has a high degree of esterification. Therefore, it has strong light and heat resistance, poor dyeing performance, and low moisture absorption rate (also called moisture regain).

In the molecular structure of cellulose acetate, the hydroxyl group on the glucose ring of cellulose is replaced by an acetyl group to form an ester bond. The degree of esterification of cellulose diacetate is lower than that of cellulose triacetate due to hydrolysis. The supramolecular structure of diacetate fiber has a larger amorphous area, while triacetate fiber has a certain crystalline structure, and the symmetry, regularity, and crystallinity of the fiber macromolecules are higher than those of diacetate fiber.

3. Structure of acetate fiber

The longitudinal fiber surface is smooth, relatively uniform, and has obvious grooves; It can be seen from its cross-sectional shape that the fiber has no skin-core structure and is in the shape of a clover leaf. The periphery is smooth and has few shallow serrations.

4. Chemical properties of acetate fiber

1. Alkali resistance

Weak alkaline alkali agent basically does not cause damage to acetate fiber, and the fiber loses weight The rate is very small. After encountering strong alkali, especially diacetate fiber, deacetylation occurs easily, resulting in weight loss, strength and modulus. Therefore, the pH value of the solution used to treat cellulose acetate should not exceed 7.0. Under standard washing conditions, it has strong resistance to chlorine bleaching and can also be used for dry cleaning with perchlorethylene.

2. Resistance to organic solvents

Cellulose acetate is completely dissolved in acetone, DMF, and glacial acetic acid, while in ethanol and tetrahydrofuran It is not soluble in vinyl chloride. Based on these characteristics, acetone can be used as a spinning solvent for acetate fiber, and tetrachlorethylene can be used for dry cleaning of acetate fiber fabric.

3. Acid resistance

Acetate fiber has good acid resistance and stability. Common sulfuric acid, hydrochloric acid, and nitric acid will not affect the strength, gloss, and elongation of the fiber within a certain concentration range; but it can Dissolved in concentrated sulfuric acid, concentrated hydrochloric acid, and concentrated nitric acid

4. Stainability

Although cellulose acetate is derived from cellulose, During the esterification process, a large part of the polar hydroxyl groups on the glucose ring of cellulose are replaced by acetyl groups to form esters. Therefore, dyes commonly used for dyeing cellulose fibers have almost no affinity for acetate fibers and are difficult to dye. The most suitable dyes for acetate fibers are disperse dyes with low molecular weight and similar dye uptake rates.

The acetate fibers or fabrics dyed with disperse dyes have bright and bright colors, good level dyeing effect, high dye exhaustion rate, high color fastness, and complete chromatography.

5. Physical properties of acetate fiber

1. Acetate fiber not only has a certain degree of water absorption, but also has the ability to be quickly removed after absorbing water.

2 The thermal stability of acetate fiber is good. The glass transition temperature of the fiber is around 185 ℃, and the melting end temperature is around 310 ℃. At the end of the heating, the weight loss rate of the fiber is 90.78%; the breaking strength of acetate fiber is 1.29 cN/ dtex, and should be 31.44%

3. The density of acetate fiber is smaller than that of viscose fiber, and closer to polyester; its strength is the lowest among the three fibers.

4. The elasticity of acetate fiber is relatively good, similar to silk and wool.

5 , The shrinkage rate of boiling water is low, but high temperature treatment will affect the strength and gloss of the fiber, so the temperature should not exceed 85 ℃.

Disclaimer: This website respects the intellectual property rights of all parties and protects the legitimate rights and interests of original authors; at the same time, it remains neutral with respect to statements, opinions, photos, etc. in articles that are reproduced, shared, etc.; the content of this website It is only for communication and learning; if you find that the content and materials of this website involve copyright or authorization issues, please do not report it, please contact us to delete it!