How to iron a cashmere coat?
(1) First of all, you should check the wash mark on the inside of the cashmere coat. It contains the ironing requirements for the coat, such as the maximum temperature, etc. When ironing the coat, you must comply with the above requirements. To avoid burning the coat.
(2) Prepare the iron and a wet cloth and start ironing. When ironing, cover the cashmere coat with a layer of damp cloth. The temperature of the iron can be higher. The water droplets on the iron will make a short “plop” sound and no water droplets will remain at the bottom of the iron. It is enough to iron the wet cloth until it is 70% to 80% dry. It should not be too dry, otherwise it will burn the surface and cause aurora. If the aurora has appeared, you can cover it with a damp cloth and gently iron it again. If your home conditions are limited, you can ask a dry cleaner to do it.
(3) When ironing the lining, spray water on the lining first and wait half an hour before ironing. There is no need to spray water on the linings of tussah silk, rayon, brocade silk, and polyester silk, but the temperature of the iron should be lower. A “plopping” sound will appear on the water droplets and rolling water droplets will appear at the bottom of the iron. The temperature of brocade silk should be lower. .
(4) When ironing the lining of an unwashed cashmere coat, do not spray water to prevent water stains. The iron temperature should be slightly lower than that of the washed one, otherwise it will easily turn yellow.
(5) When ironing the reverse side of a large collar, the wet cloth should be ironed dry and the collar should not be exposed under the collar. Plush and gold velvet collars should not be ironed too dry. After ironing, use a brush to smooth the hair and make it stand up. Do not cover the leather collar with wet cloth.
(6) When ironing the sleeves of a cashmere coat, stuff a small pillow into the rotator cuff, hold up the small pillow with your left hand, cover it with a layer of wet cloth, and iron the rotator cuff to make the shoulders and armholes flat. Sleek.
Requirements: Men’s cashmere coat lapel collars must be ironed firmly, women’s lapel collars should be ironed into a flexible shape, men’s cashmere coat sleeves should be ironed into a round shape on the front, and flat on the back. The coat sleeves should be ironed into a round shape on the front and back.
(1) When ironing cashmere coats, the temperature is most critical and should be controlled within 160C°, or within the temperature indicated on the coat label. Steam ironing has the best effect.
(2) When steam ironing, perform it 1-50cm away from the cashmere coat; or cover the wool coat with a towel before ironing; this will neither damage the wool fiber nor leave any residue. Traces of ironing.
(3) Cashmere coats should not be dry-ironed, and the iron should not be in direct contact with the clothes to avoid the generation of aurora.
(4) Cashmere coats should not be ironed until they are completely dry. The moisture content should be about 5%. Hang them on a hanger to dry naturally after ironing, making them appear more natural and soft.
(5) It is best to wash the cashmere coat that needs to be ironed first, otherwise the stains on the clothing will be more obvious after ironing.
(6) When ironing a cashmere coat, you can spray a little toilet water on the cloth, so that the ironed clothes will have a pleasant and lasting fragrance.
The velvet of my woolen coat becomes shiny after being ironed.
What should I do?
(1) Dilute it with vinegar and spray it on the area damaged by ironing, then apply it with a damp towel and slowly dry it in the shade.
(2) You can twist the bread into powder and spread it in a bright place, then iron it with an iron. You can also use a small amount of talcum powder to spread on the surface of the clothes. After five minutes, adjust the iron to steam temperature and iron the cashmere coat with a cloth, and the coat can return to its original appearance.
(3) Pickling: Soak in glacial acetic acid aqueous solution with a concentration of 3-5% and a temperature of 50°C for 3-5 minutes, and then rinse with clean water.
(4) Use a steam iron to apply steam to the aurora area, and then brush it repeatedly with a soft brush;
(5) Gently polish the aurora area with extra fine sandpaper , attention to prevent backfire.
(6) Re-clean the damaged areas of the cashmere coat and iron it in the correct way.
