Under normal circumstances, when we buy clothes, we need to choose clothes that suit our own size, but do you know that during the mass production process of these clothes of different sizes, before leaving the factory, Specialized inspectors are required to measure the size. Only after each size has been accurately measured can it be packaged, shipped out of the factory, and sold!
Now popularize it to everyone Schematic diagram of the measurement method of various parts of general finished clothes in bulk factories: for reference!
Special attention needs to be paid: The measuring methods of the following measuring parts are the basic measuring methods under normal circumstances. Different customers may have small differences!
In addition As a qualified clothing pattern maker, you must first know the measurement method of each part of the clothes. This is the most basic requirement!
1. Figure 1: T120 mark: Represents the measurement of the length of the front garment. , measure from the shoulder height to the hem edge
2. As shown in Figure 2:
T100 mark: represents the length of the back center garment, measured from the bottom of the back center collar to the hem edge , excluding collar height!
T280 marking: represents the measurement of the cuff seam height
T250 marking: represents the measurement of the sleeve opening size of the short sleeves
T270 Marking: Measure the middle back sleeve length from the middle back collar, through the shoulder width point, to the cuff edge
3. Figure 3:
T323 Marking: Representative Measure the size of the over-the-shoulder, which is the size before the shoulder seam.
T440 mark: represents the length of the front center zipper.
T200 mark: represents the arc of the front clamp circle. Size,
T140 mark: represents the measurement of the bust size, from the bottom of the clip, that is, 1 inch under the armpit.
T160 mark: represents the measurement of the hem size, from Measure straight from the upper seam to the seam, that is, lay straight from left to right
A100 mark: represents the length of the side slit,
T161 mark: represents the hem pressure Line height dimension
4. Figure 4:
T198 label: represents the measurement of the shoulder slope, the vertical depth dimension from the shoulder height point to the shoulder width point
T199 Marking: Represents the measurement of the depth of the clamp circle, measured from the shoulder height to the vertical depth of the bottom of the clamp
T670 Marking: Represents the measurement of the width of the upper pocket of the front and middle squirrel bag
T690 mark: Represents the measurement of the middle height of the front center squirrel bag, from the top edge of the bag to the bottom edge of the bag
T680 mark: Represents the measurement of the width of the front center squirrel bag
5. As shown in Figure 5:
T170 mark: Measure the back shoulder width from the left shoulder seam to the right shoulder seam, and measure straight from seam to seam!
T650 Note: It represents the measurement of the height of the back hem, which is the height of the dovetail. Straighten the left and right side seams and measure vertically to the height of the hem.
6. Figure 6:
T300- 1 mark: represents the measurement of the back collar width, measured from the collar seam, seam to seam
T300-2 mark: represents the measurement of the rear collar width, measured from the collar edge. Side-to-side dimensions
T320-1 marking: represents the measurement of the depth of the front collar, which is measured from the collar edge at the shoulder height to the front collar edge
T320-2 marking : Represents the measurement of the depth of the front collar, which is measured from the height of the shoulder to the deep collar seam of the front collar.
7. Figure 7:
T310-1 is marked: Represents the measurement of the depth of the back collar, measured vertically from the shoulder height point to the deep collar edge of the back collar
T310-2 Note: Represents the measurement of the depth of the back collar, measured from the shoulder height The point is measured vertically from the shoulder seam to the deep seam of the back collar
T390 mark: represents the distance between the left and right collar tips of the front collar
T391 mark: represents the distance between the front collar and the front collar after it is buttoned. The size of the distance between the collar and the face
T190 label: represents the measurement of the chest width. Generally, the position of the front chest width is how many dimensions below the shoulder height. The measurement is based on each customer. Depends on different requirements
T180 mark: represents the measurement of the back width. Generally, the back width is at the same position as the front chest width, and it is measured from the measurement below the shoulder height. Depends on each customer’s requirements
A100 marking: represents the length of the center slit after measurement
8. As shown in Figure 8:
T199 marking: Represents the depth of the clamping circle, measured vertically from the height of the shoulder to the size of the bottom of the clamping circle
T260 mark: represents the measurement of the middle back sleeve length of the raglan sleeve: measured from the middle back collar to the cuff size
T260 mark: p>
T100 Marking: Represents the measurement of the length of the back garment, from the center back collar seam to the hem edge
T210 Marking: Represents the measurement of the sleeve width. The specific requirements shall be determined by the customer. How much is the measurement from under the collar seam to the sleeve width?
T220 mark: represents the sleeve fat size, measured 1 inch from the bottom of the clip
T230 mark: represents the sleeve elbow circumference size, It is also necessary to measure the size from under the collar seam according to the customer’s requirements
T231 mark: represents the small sleeve elbow size. It is also necessary to measure from the bottom of the collar seam or the size from the edge of the cuff according to the customer’s requirements. Depends on location
